Do you know the vibration device of the thickener?

 The thickener is a solid-liquid treatment equipment used in the concentrator. In order to improve the treatment effect of the thickener per unit area and improve the efficiency of the thickener, the high-efficiency thickener or the inclined plate thickener will be selected. High-efficiency thickeners will increase the height of the straight wall section of the thickening tank, and use appropriate fabrics to add flocculants to improve concentration efficiency. In some concentrators, the materials are small and viscous, the sedimentation speed is slow, and the flocculant cannot be used due to the nature of the material. At this time, the inclined plate thickener is used. The thickening pool of the inclined plate thickener will be divided into a number of equally divided sectors, and each sector will be arranged at a certain interval into a certain angle of inclined plate or inclined tube. The fine particles of the material in the lower part of the thickening tank will naturally settle on the inclined plate and the inclined tube. In this way, the settling distance of the material particles can be shortened by the inclined plate or the inclined tube, and the settling time can be reduced to increase the thickener. The precipitation area to improve concentration efficiency.

The inclined plate thickener will be affected by the nature of the material and the material of the inclined plate during use, and the phenomenon of adhesion between the inclined plates will often occur, which is what we often say that the material that settles on the inclined plate or the inclined tube is not Continuous sliding, on the contrary, the material will settle to a certain thickness before the whole fall. This phenomenon is commonly called hanging material. The whole falling material will be filled with the cone pit of the thickening tank, but because the thick material is too thick, it will cause the harrowing phenomenon after the lifting device fails. There may even be a phenomenon that the inclined board or the inclined board collapses. When the inclined plate thickener has material hanging, the user will use high-pressure water flushing to solve the problem. During the reprocessing process, the overflow water of the thickener will run off and the thickener will stop to clear the pool, which will affect the thickener. Normal use.

In response to this situation, a vibration device for the inclined plate thickener was designed. This vibration device is not only suitable for ordinary central drive thickeners, but also for high-efficiency deep cone thickeners and other types of inclined plates or inclined tubes. Thickener.

The vibration device is generally composed of a vibration rod, a connecting rod, a vibration ring and an electric control box. The vibrator consists of a vibration motor and a motor frame. Composed of shock-absorbing spring and support frame. When installing the vibrator, the support in the vibrator is placed on the bridge of the thickener on site and adjusted to a suitable place for fixing. The lower part of the connecting rod and the vibrating ring can be fixed with bolts. The connecting rod, the motor frame and the vibration ring will be rigidly connected. In order to reduce the impact of the vibrator on the bridge frame of the thickener during the working process, a shock-absorbing spring can be used between the vibrator and the bridge frame to relieve the high-frequency excitation generated by the vibrator Vibration of the force on the bridge.

When the inclined plate vibration machine is working normally, the thickener enters the lower part of the thickening tank from the feeder. The coarse particles in the incoming slurry naturally sink, and the fine materials in the lower part of the thickening tank will naturally sink into the cavity of the inclined plate, but due to the small distance between the inclined plates, the particles only need to settle a small distance , You can settle on the inclined board.

The installation structure of the vibrator device is very simple, easy to install, and reliable in operation. It is very suitable for the beneficiation method where the material is small and thick, the speed is very slow, and it is not easy to fall off. The vibration device can be used for power-driven thickeners equipped with inclined plates or inclined tubes. This vibrating device has a certain reference effect for the technical reform of the new thickener and the technical improvement of the old inclined plate.

What factors can cause the flotation machine to not work normally?

 The flotation machine is a full-grain flotation machine, suitable for both coarse and fine particle separation. After the Chinese pulp of the GLF flotation machine is processed, the flotation machine must be agitated and aerated, so that the mineral particles can be fixed on the bubble and float to the surface to form a foam product, and the rest will be stored in the pulp for separation . The GLF flotation machine is not only a stirring device, but also capable of forcibly blowing in air under the external special action. The mechanical stirring device is used to agitate the slurry to distribute the air flow, and the aeration and stirring of the slurry work separately. The GLF type aerated stirring flotation machine can be adjusted according to its own needs at best. Only in this way can it be helpful to improve the sorting capacity and processing capacity of the flotation machine. However, due to the larger processing capacity and the shallower flotation cell, the required power consumption is lower. GLF flotation opportunities because the impeller speed is low, the concentration of the slurry when passing through the impeller will also be lower, and the ore particles will become finer, which will correspondingly reduce the efficiency of flotation. In this case, the impeller and stator will reduce wear. There is a grid plate in the flotation tank, which will cause a suspended layer of coarse particles, which can make the surface of the slurry more stable and make the technical performance better. In this case, it is beneficial to the coarse particle flotation.

There are several common faults of GLF:

(1) The cover plate or stator screw of the flotation machine is off.

During the entire operation of the flotation machine, the cover plate and screws will easily fall off due to the rotating impact and vibration of the flotation machine itself. This situation will affect the normal operation of the flotation machine. Therefore, the flotation machine is carefully checked before each work.

(2) The bottom of the flotation machine is worn.

If the flotation machine runs for a long time and rotates strongly, the bottom of the tank will be worn and thinned, and the surrounding guard plate will be worn and deformed, and under the action of the flotation agent, the bottom of the tank will also be worn and deformed. Therefore, when wear occurs, It is necessary to repair welding in time.

(3) Pry up the bottom guard plate of the groove.

During the flotation process, the tank bottom guard plate protects the bottom of the tank. When the impeller rotates strongly, the circulation of the ore in the flotation tank will be accelerated. In severe cases, the charge will increase and the guard plate will be pryed. It will cause an accident.

(4) Wear and corrosion of impeller and cover plate.

The impeller and cover plate are the core components of the flotation machine, and it is also a position that is easy to wear. It is directly related to the degree of aeration of the slurry during the flotation process. The degree of agitation in the sea area, but because the flotation machine is in the process of long-term work, it will The impeller also damages the cover plate, so the impeller and cover plate need to be repaired and replaced for a long time.

(5) The spindle is worn out.

When the spindle is in use, the rubber sheath of the spindle should be protected. After the rubber sheath is worn, the spindle wears quickly under the action of the internal circulation of the slurry, and it is very easy to break the shaft. Therefore, it should be updated frequently during the inspection. Rubber sheath.

(6) The bearing clearance becomes larger.

When the main shaft of the flotation machine is running at high speed, the bearing gap will easily become larger, which will damage the bearing. At this time, only the tightness of the inner and outer gaskets of the bearing needs to be adjusted.

(7) The motor generates heat.

During the operation of the flotation machine, too much sand accumulates in the flotation cell, the cover plate and the ore tube fall off, and the circulation of the ore tube is too large, which will cause the electric heater to heat up. In this case, the cover plate and the ore tube should be provided. Tighten it in time when it is loose, and replace it in time when the circulation volume of the ore pipe is too large.

    As mentioned above, during the use of the GLF flotation machine, due to the harsh environment and poor maintenance during use, various problems will occur. Therefore, timely attention and regular maintenance should be carried out to prevent the work process from being blocked. Off.

How to use large flotation machine to separate copper and molybdenum ore

 About 90% of non-ferrous metal recovery in the world will use flotation method, in order to realize mineral flotation flotation machine plays a great role. Large-scale flotation machine can significantly improve the processing capacity of beneficiation, reduce consumption, and obtain higher benefits.

The flotation machine is a motor that drives the rotating shaft to rotate the impeller. Under negative pressure, the pulp moves between the impeller and the stator, and the centrifugal blower is evenly dispersed in the air through a porous cylindrical air distributor for mineralization. After the stator is stabilized, it rises to form a stable foam layer, and enters the next operation through the upper foam tank. The remaining slurry will flow through the flow holes in the tank wall to the next tank for sorting, and finally become tailings.

The main characteristics of tooth decay of the super large flotation machine are:

(1) The pulp aeration and bubble mineralization effect is good.

The air coming in from the blower will directly enter the air inlet on the top of the flotation machine through the air duct. A regulating valve that controls the air volume is installed at the air inlet. The air can directly enter the hollow shaft to ensure that the slurry in the flotation machine is not fully affected by the equipment. Mineralization. And a good amount of aeration can effectively suspend the mineral particles in the entire flotation tank and evenly distribute the bubbles.

(2) Energy saving and loss of equipment.

Before the flotation machine, air was directly fed between the impeller and the stator by the blower. After the hollow shaft rotates, the equipment can make the air into the suspension state formed after stirring at low speed and enter the selection for selection. The stator adopts The form of low damping changes the direction of the slurry flow to the radial direction, which can reduce the resistance circulation and power consumption of the slurry.

(3) High efficiency of automatic liquid level control. The slurry level in the flotation machine can be detected by a slurry level gauge, which can realize automatic control of the slurry level. The tailings box and the middle box have a cone valve to control the flow of the slurry, which is controlled by a pneumatic actuator, so that it can be used for full adjustment of the slurry.

(4) Conducive to improving the selection effect. The deep cone structure can mineralize the pulp to provide a stable foam zone and a longer separation zone, so that low-pressure air can be fully dispersed in the solid, liquid, and gas three-phase strong turbulent mixing zone at the bottom of the flotation machine, which can generate bubbles If it is fully utilized, there is a large speed difference between the bubbles and the pulp. There are more opportunities for fine particles to contact the bubbles, and the fine particles will fully float out. The slurry will sink, increase the chance of collision of bubbles and increase the chance of flotation.

(5) Convenient operation and management of equipment.

Can drive the load to start; advanced slurry level control olefin; reduce short circuit circulation; spare parts wear light, low maintenance and repair costs; simple structure, easy maintenance; low energy consumption; good air dispersion; low chemical consumption, saving investment and so on.

Research on unit consumption and service life of ball mill liner

 The liner is a key easily damaged part for the ball mill. The unit consumption and service life of the liner are inseparable from the working efficiency of the ball mill.

     The factors that affect the wear rate of the liner mainly include the corresponding particle size and hardness of the material to be ground, how much electricity is needed to grind each ton of material, the diameter of the mill and its speed, the structure of the liner and the wear resistance of the liner material The percentage of the weight and volume of the original lining board and the original lining board. For the current process, the metal liner is mostly low-grade ore first-stage grinding, but for most low-grade ore, the content of silica and other hard grinding and corrosive minerals are very high, but in this case In the second-stage grinding process, many concentrators will choose ball mills to use rubber liners.

     The service life of the cylinder liner is four factors: macroscopically speaking, the resistance to impact failure damage; macroscopically speaking, the resistance to fatigue failure damage; the resistance to surface cutting or cutting wear; the surface microscopic resistance to impact fatigue and wear Kind of operating conditions.